液压多功能小件落物打捞器的研制与应用

由于侧钻井、水平井特殊井身结构限制，常规的小件落物打捞器打捞成功率低。为此经过认真分析和现场实践，将常规机械操作的一把抓改成液压操作，常规强磁打捞器的圆柱形平面磁铁改成具有伸缩性的磁针，同时结合套铣筒，研制出一种液压多功能小件落物打捞器，克服了侧钻井、水平井井身结构的限制，大大提高了一次打捞成功率，现场应用效果明显。     

Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

挡渣球和挡渣塞技术在转炉炼钢的应用

介绍了档渣球和挡渣塞技术在转炉炼钢的实际应用，有利于降低原材料消耗、增加企业效益。     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.     

东方N-18250-2型凝汽器胶球清洗系统改造

对湘潭电厂存在已久的胶球清洗装置收球率低的问题进行了深入探讨，结合电厂对胶球清洗系统的改造、试验过程，分析并提出了影响胶球清洗装置清洗效果及收球率的诸多原因及其解决方法。     

机械合金化的原理及在磁性材料研究中的应用

介绍了机械合金化的原理和描述机械合金化过程的理论模型。综述了机械合金化在磁性材料研究中的应用，并对目前研究中的存在的问题及发展前景进行了分析。